The most detailed ISOFIX installation process in the whole network – rear seat installed children’s seat ISOFIX interface

Written in front

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Nowadays, children’s seats have several interfaces such as Latch, ISOFIX, and ISOFIX is more common, but some old models do not have such an interface, so there will be some restrictions when purchasing children’s seats.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

I bought a European security seat before, but I bought it until ISOFIX interface, so I installed a set, this time I specifically presented to everyone, I hope to give some friends who have the same needs by reference.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

This article is as follows:

I. Overview

Second, the pre – test

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Third, accessories and tools

Fourth, install

Five, summary

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

The ISOFIX interface is actually two metal rings, and there are two crocodile pliers under the safety seat, and the bite of the metal ring completes the connection between the interface.

Interface docking

When installing, the two metal rings need to be fixed to the frame with the seat belt card, so as long as there is a metal ring fitting and the corresponding disassembly tool, it can be completely DIY.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Because the model is different, please make the necessary check before installation, in general.

TIPS:

1. Search for this kind of interface on Taobao, enter models + ISOFIX can generally see probably

2, remove the rear seat cushion, check the secure method of the seat belt, fixed the screw specifications used, and the tools needed to remove the screws, especially if the sleeve tool is required, please contact it under specific.

The fittings are naturally the ISOFIX interface searched in the previous step, as well as the attached gasket, plastic sheath.

Tools need to remove the screws, there is necessary words to

Sleeve tool

!

First pick up the accessories and tools

Two metal rings

Activity wrench and universal wrench

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Universal wrench is the following, nor must

There is also a sleeve tool:

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Tri-head sleeve

Maximum 17mm

Take a few details:

Back seat intermediate metal ring

▲ ▼ These two metal rings are mounted on the driving side, and there is also the side of the board, pay attention to distinguish

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Rear seat driving side metal ring

Close-up:

Steel cross section, thickness is also

Screw holes

Extended screws:

Extended screw cap is 1mm in diameter of the screw cap on the car

Note from accessories and tools:

1, pay attention to the thickness of the ISOFIX metal ring steel plate,

Most of Taobao is now five mm B-class steel plates. It is estimated that the industry is this peer practice. This is enough, no problem.

2, pay attention to accessories,

A. Because it is necessary to join a seat with a seclusion card, it is necessary to have a seller to have a long screw.

B. The screw is long, the length is not too long, the screw is not good, so it has to be equipped.

C. If you often disassemble the seat, there should be a plastic sheath of the bayonet to avoid the surface of the seat.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

3, determine if a sleeve tool is needed,

The sleeve tool is a professional tool for auto repair, but it is common in the auto repair shop, but ordinary families, community properties, corporate teams generally don’t, so when you check it, take a wrench, my home is, a screw The screws that can be used in the back seat drive side seat belt in a deep nest, the wrench cannot be buckled and rotated, so it also has a sleeve tool.

The sleeve tool is related to the screw size, but you can also try the online activity tool, just generally more expensive, if it is not common, or only one is a comparison. The screw on my car is 17mm, so it takes 17mm, but the resulting length screw is 16mm (different screw cap, the screw is the same), and the phase difference is 1 mm or can be used.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Accessories tools can be dried. There are a few small attention before doing it:

1, find a sunny day,

The light is bright, don’t toss in the ground, it is the way to dry in the back row, and the light is dark, it will be very delayed.

2, stop the car, don’t stop,

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Although it is ready to work, at least one hour is taken, don’t do half of the car.

3, push the seat of driving and co-driver to the fore,

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Leave the maximum space for the rear row.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

4, it is best to bring a glove,

There is also a lot of places that need to be grinded.

Ok, start to make a wave of installation process:

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

1, remove the seat pad

Remove the rear seat pad, you need to make a little, this is before being opened:

To start from the corner of the seat, the following snaps are on both sides, this location:

After disassembling, you can see that the seat cushion is also very dirty, just because of the way:

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

The seat cushion is a buckle of plastic, and there is a metal ring under the seat cushion:

After the disassembly, you can see the fixed screw of the intermediate seat belt card:

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

And, fixed screws on the driving side:

Two together to see:

2. Remove the middle seat belt card holder in the back seat

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Remove the screw, you can use the wrench or sleeve tool.

After removing, you should pay attention to the laminated sequence of various components on the screw. When changing the screw, in the original order, the installed interface should be placed at the top, and the gasket is placed at the bottom layer.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Remove the laminated order after the screw

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Remove the screw hole

Long short screw comparison

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

After removing, set the interface component, this location is used, which is a smaller metal ring, and the larger metal ring is used in the rear seat drive side.

Place in the original order

Then you turn back, you should take it to the last time, you want to slave.

You can turn the metal interface to the left side to turn a certain angle before thoroughly tightening, and then thoroughly tighten so that the interface will rotate to the vertical position.

Screw it back with universal wrench

I am disassembled with universal wrench, and the sleeve tool will make better!

3. Remove the rear seat drive side seat belt stationary seat

The rear seat drive side must be used with sleeve tools because the wrench is not going down. The situation is the same as just now. A few pictures, let’s take a look:

Solder tool

Removed screw

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

The things in this screw are more, but it doesn’t matter, how to make it back.

Patch metal ring connection

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Next, use the sleeve tool to remove it, the effect is as follows:

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

4, restore seat cushion

After the two metal rings are installed, you can restore the seat cushion, which is also very simple.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Before you re-buck the seat cushion, look at the two metal rings:

When the seat is buckle, pay attention to the two safety belts of the above figure out.

After the seat is buckle, put the plastic sheath and protect the seat cushion, there is no use:

Push the metal ring in this direction.

Finally installed the effect:

The above, all installed.

Interface plug effect:

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

The seat docking isofix interface

1. Installing this stuff, is not difficult, as long as I follow the previous instructions, the pre-pre-test can be checked, and the can be installed, and the sleeve tool is required and the sleeve tool is needed.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

2, the entire installation value of 200 yuan = accessory 100, the sleeve tool 20, the labor fee is about 80 (the new line price), after reading my Raiders, the installation time can be controlled within 1 hour.

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

3, this installed model is 08 Excelle 1.6AT NAVI

I. Overview

Second, the pre – test

Third, accessories and tools

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

Fourth, install

Five, summary

TIPS:

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

TIPS:

TIPS:

全网最详细ISOFIX安装过程——后座加装儿童座椅ISOFIX接口

TIPS:

Patch metal ring connection

RELATED POST

The sun is most suitable for the five games that play with the sun. If you haven’t played it, you will be out!

The sun is most suitable for the five games that play with the sun. If you haven't played it, you…

Bi Ya Bi: RockPort RocSport Lite men’s lace -up business leather shoes $ 56

Bi Ya Bi: RockPort RocSport Lite men's lace -up business leather shoes $ 56 RockPort is a well -known American…

Dry goods | How much do you know about all kinds of skin care?

Dry goods | How much do you know about all kinds of skin care? Last time, I explained to you…

What is the effect of using activated carbon filters to use activated carbon filters?

What is the effect of using activated carbon filters to use activated carbon filters? Soft -water station usually uses sodium…